Search found 254 matches

by 4DThinker
Sat Apr 20, 2019 6:59 pm
Forum: Machine Mechanics
Topic: Y axis limit error
Replies: 1
Views: 1333

Re: Y axis limit error

I'd check the wires connected to the Y limit switches. Those are mounted under the gantry side plates. They may have worked loose from the switch terminals. Anything that causes the limit circuit to open up will throw an error. On our Nebula the X axis switches (mounted on the ends of the gantry bea...
by 4DThinker
Thu Mar 21, 2019 7:10 pm
Forum: Open Talk
Topic: Limit Switch Errors
Replies: 3
Views: 832

Re: Limit Switch Errors

If you've had your machine awhile, the best solution is to replace the switches. Limit 0 is the X axis and those switches are on the ends of the gantry beam. I oversee three Probotix CNCs and my students have a tendency to jog the Z axis to the top before homing the machines which eventually bends/f...
by 4DThinker
Sat Feb 16, 2019 10:48 am
Forum: Projects
Topic: Adjustable Angle Clamping Fixture
Replies: 26
Views: 27045

Re: Adjustable Angle Clamping Fixture

Latest version of my jig now installed on a Comet (GX2525).
GX2525_KSU.jpg
GX2525_KSU.jpg (1.49 MiB) Viewed 3553 times

4D
by 4DThinker
Sat Dec 29, 2018 2:36 pm
Forum: Projects
Topic: Pod Organizer
Replies: 3
Views: 722

Re: Pod Organizer

Looking good. If I drank coffee I'd be stealing your idea for myself.

4D
by 4DThinker
Sat Dec 29, 2018 2:34 pm
Forum: Projects
Topic: Mailbox Address Label
Replies: 3
Views: 1262

Re: Mailbox Address Label

Looks like a great use for cutting board blanks to me. I'll be curious to know how well they look after a few years outside. You might look into the temperature expansion/compression values of what is likely HDPE relative to the same values for the metal mailbox. Just thinking of the future.... 4D
by 4DThinker
Wed Dec 26, 2018 5:27 pm
Forum: Projects
Topic: Joints Anyone
Replies: 85
Views: 47724

Re: Joints Anyone

Thanks Hannah. After helping several students cutting mitered corner joints for a box project I woke up the following day thinking it was a shame to have essentially thrown away the mitered waste to leave a weak joint. This joint still cuts away exactly the same amount of the 45 degree end but leave...
by 4DThinker
Wed Dec 26, 2018 4:57 am
Forum: Projects
Topic: Joints Anyone
Replies: 85
Views: 47724

Re: Joints Anyone

Internal Mortise & Tenon for mitered box corners. The boards were mounted at 45 degrees on my angle jig. The same toolpath file was cut on each side. Invisible when assembled. Clamping when gluing up is easy. 4D https://1.bp.blogspot.com/-yAN_yW9GbKY/WyErGr-L7pI/AAAAAAAACvY/5fXIspVhWvUW8f1ZCPHaT...
by 4DThinker
Sun Dec 23, 2018 5:18 pm
Forum: Machine Mechanics
Topic: Jog pendant? Purpose?
Replies: 3
Views: 436

Re: Jog pendant? Purpose?

END on the keyboard followed with ENTER will effectively touch off (zero) the active axis (last direction you jogged or hit on the keyboard (x,y,z)). You can also switch quickly between Continuous and the last Increment jog step you've chosen by hitting C and I respectively. A list of all the keyboa...
by 4DThinker
Tue Dec 18, 2018 8:22 am
Forum: Machine Mechanics
Topic: Alignment issue observed when cutting spoil board
Replies: 2
Views: 560

Re: Alignment issue observed when cutting spoil board

Old post, but I'll chip in anyway. We have a Meteor where I work that produced similar lines when milling off the spoilboard with a 1" end mill. A quick check of the Z axis against the perimeter frame showed Z was tipped back about 2 degrees. To fix this we took out the front bolts holding the ...
by 4DThinker
Tue Dec 18, 2018 8:16 am
Forum: Machine Mechanics
Topic: Jog pendant? Purpose?
Replies: 3
Views: 436

Re: Jog pendant? Purpose?

Using one vs using the keyboard is just a matter of personal preference. These CNCs used to come with a game controller for jogging the spindle around, but using that was IMO slower and less precise than using the keyboard. I don't have a jog pendant, but have even looked into using just a wireless ...

Go to advanced search