Wooden Waves

Show off your handy work here
sgano
Posts: 14
Joined: Sun Oct 11, 2015 7:15 pm

Wooden Waves

Postby sgano » Sun Aug 07, 2016 10:03 pm

Tried out 2-sided machining and learned a lot!

wavefield_maple_2016_SEG.jpg
wavefield_maple_2016_SEG.jpg (3.65 MiB) Viewed 4679 times

sgano
Posts: 14
Joined: Sun Oct 11, 2015 7:15 pm

Re: Wooden Waves

Postby sgano » Sun Aug 07, 2016 10:05 pm

Here is picture after rough cutting the bottom side:
IMG_6064.JPG
IMG_6064.JPG (1.85 MiB) Viewed 4678 times

Juan Hidrovo
Posts: 245
Joined: Sun Jan 17, 2016 8:33 pm

Re: Wooden Waves

Postby Juan Hidrovo » Sun Aug 07, 2016 10:38 pm

sgano

Wow.
Looks super. Keep posting.

User avatar
HANNAH024
Posts: 289
Joined: Fri Aug 21, 2015 9:57 am

Re: Wooden Waves

Postby HANNAH024 » Mon Aug 08, 2016 5:38 am

Awesome - Good Job.
I'm full of questions.
How long did it take to cut both sides of the wave project?
What cutter did you use?
and what was the Depth of cut per pass?
It is what it is!
Have a great day.
HANNAH

Hannah7824@att.net
Posts: 82
Joined: Sat Aug 22, 2015 4:36 pm

Re: Wooden Waves

Postby Hannah7824@att.net » Mon Aug 08, 2016 9:22 am

Looks good What method did you use in the software and on the Cnc router to index your program and material so that when you flip it over you still have a known orgin or index point.
It is sometimes a pain but results like yours make it worth the effort! Nice job

C6MFG
Posts: 17
Joined: Tue Sep 01, 2015 6:15 pm

Re: Wooden Waves

Postby C6MFG » Tue Aug 16, 2016 6:01 pm

Very cool!

sgano
Posts: 14
Joined: Sun Oct 11, 2015 7:15 pm

Re: Wooden Waves

Postby sgano » Thu Aug 18, 2016 2:30 pm

(Sorry for the slow reply - I did't realize I hadn't selected the option to get e-mail notifications)

First off thanks it was a really fun project! Now to answer your questions:

1) Machining time: Each side took about 20 minutes for the roughing cut then about 40 minutes for the finishing pass. So it took about 2 hours of total machine time for the entire project.
2) Cutters used: I used a standard 1/4" endmill for the roughing, then a 1/4" Tapered Ball-nose from Precise Bits for the finishing.
3) Pass cut depths: I used 1/8" passes and then just left a 0.012" machining allowance for the finishing pass.
4) Indexing for flipping the part over: On the top side I cut holes beside the part that would fit some dowels I had. Then when modeling the bottom side I just inverted the hole locations. Then when I ran the bottom side, I clamped a piece of MDF down, set the zero point and the routed out the same holes. In the holes I inserted dowels. Next I put the material back on face down aligning the dowels into the holes (this made sure I had the x-y plane perfectly aligned) and then finished the bottom side. I was quite worried that the tabs would break during machining on the bottom side since they were only 1/8" thick -- but since there were 8 of them they ended up being very sturdy. I got this method from a Vectric tutorial on a Two Sided Leaf Bowl project.


Return to “Projects”

Who is online

Users browsing this forum: No registered users and 3 guests