Tooling - Revision history

Admin: updated links

2018-08-14T22:59:48Z

updated links

Admin at 17:05, 8 February 2018

2018-02-08T17:05:48Z

Admin at 15:02, 14 September 2017

2017-09-14T15:02:31Z

Admin at 15:02, 14 September 2017

2017-09-14T15:02:08Z

Admin at 15:01, 14 September 2017

2017-09-14T15:01:56Z

Admin at 17:12, 20 February 2016

2016-02-20T17:12:27Z

Admin: Created page with "Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your tol with calipers, you will most often find that the diameter at the flutes is not even what w..."

2016-02-20T17:12:07Z

Created page with "Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your tol with calipers, you will most often find that the diameter at the flutes is not even what w..."

New page

Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your tol with calipers, you will most often find that the diameter at the flutes is not even what was advertised. The best way to address it is to make a test cut in the exact material at the same feed rate and depth of cut, then measure the width of the actual cut and use that as the diameter of your tool in your CAM software.

@@ Line 1: / Line 1: @@
 Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your tool with calipers, you will most often find that the diameter at the flutes is not even what was advertised. The best way to address it is to make a test cut in the exact material at the same feed rate and depth of cut, then measure the width of the actual cut and use that as the diameter of your tool in your CAM software.
-www.precisebits.com
+=== Suggested: ===
+* https://precisebits.com/
-www.magnate.com
+* https://www.magnate.net/
+* http://drillcity.stores.yahoo.net
-http://drillcity.stores.yahoo.net
+* Carbon Fiber: http://drillcity.stores.yahoo.net/10pcset.html
+* https://www.toolstoday.com/p-6231-18-pc-cnc-signmaking-advanced-router-bit-collection-14-inch-shank.aspx
 Carbon Fiber: http://drillcity.stores.yahoo.net/10pcset.html
-−
 https://www.toolstoday.com/p-6231-18-pc-cnc-signmaking-advanced-router-bit-collection-14-inch-shank.aspx

← Older revision		Revision as of 17:05, 8 February 2018
Line 6:		Line 6:

	http://drillcity.stores.yahoo.net		http://drillcity.stores.yahoo.net
		+
		+	Carbon Fiber: http://drillcity.stores.yahoo.net/10pcset.html

	https://www.toolstoday.com/p-6231-18-pc-cnc-signmaking-advanced-router-bit-collection-14-inch-shank.aspx		https://www.toolstoday.com/p-6231-18-pc-cnc-signmaking-advanced-router-bit-collection-14-inch-shank.aspx

← Older revision		Revision as of 15:02, 14 September 2017
Line 4:		Line 4:

	www.magnate.com		www.magnate.com
		+
		+	http://drillcity.stores.yahoo.net

	https://www.toolstoday.com/p-6231-18-pc-cnc-signmaking-advanced-router-bit-collection-14-inch-shank.aspx		https://www.toolstoday.com/p-6231-18-pc-cnc-signmaking-advanced-router-bit-collection-14-inch-shank.aspx

@@ Line 1: / Line 1: @@
 Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your tool with calipers, you will most often find that the diameter at the flutes is not even what was advertised. The best way to address it is to make a test cut in the exact material at the same feed rate and depth of cut, then measure the width of the actual cut and use that as the diameter of your tool in your CAM software.
-www.precisebit.com
+www.precisebits.com
 www.magnate.com
 https://www.toolstoday.com/p-6231-18-pc-cnc-signmaking-advanced-router-bit-collection-14-inch-shank.aspx

← Older revision		Revision as of 15:01, 14 September 2017
Line 1:		Line 1:
	Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your tool with calipers, you will most often find that the diameter at the flutes is not even what was advertised. The best way to address it is to make a test cut in the exact material at the same feed rate and depth of cut, then measure the width of the actual cut and use that as the diameter of your tool in your CAM software.		Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your tool with calipers, you will most often find that the diameter at the flutes is not even what was advertised. The best way to address it is to make a test cut in the exact material at the same feed rate and depth of cut, then measure the width of the actual cut and use that as the diameter of your tool in your CAM software.
		+
		+	www.precisebit.com
		+
		+	www.magnate.com
		+
		+	https://www.toolstoday.com/p-6231-18-pc-cnc-signmaking-advanced-router-bit-collection-14-inch-shank.aspx

← Older revision		Revision as of 17:12, 20 February 2016
Line 1:		Line 1:
−	Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your ~~tol~~ with calipers, you will most often find that the diameter at the flutes is not even what was advertised. The best way to address it is to make a test cut in the exact material at the same feed rate and depth of cut, then measure the width of the actual cut and use that as the diameter of your tool in your CAM software.	+	Be aware that an 1/8" tool may not make an 1/8" cut. In fact if you measure your tool with calipers, you will most often find that the diameter at the flutes is not even what was advertised. The best way to address it is to make a test cut in the exact material at the same feed rate and depth of cut, then measure the width of the actual cut and use that as the diameter of your tool in your CAM software.