Difference between revisions of "Sample G-Code"
From PROBOTIX :: wiki
| (3 intermediate revisions by the same user not shown) | |||
| Line 18: | Line 18: | ||
</pre> | </pre> | ||
| − | Tool Sensor Test: This code will loop through tools 1-4 to prove that the tool sensor is working. | + | Tool Sensor Test: This code will loop through tools 1-4 to prove that the tool sensor is working. This calls the tool, measures the length, drives it to zero, then pauses for 3 seconds before calling the next tool. |
<pre> | <pre> | ||
% | % | ||
| Line 52: | Line 52: | ||
G4 P3 | G4 P3 | ||
| + | M30 | ||
| + | % | ||
| + | </pre> | ||
| + | |||
| + | Counter-bored Hole Pattern: This code will create a pattern of counterbored holes in your spoilboard using an 1/8" end mill. This program demonstrates nested loops. | ||
| + | |||
| + | <pre> | ||
| + | % | ||
| + | (create counterbored holes for threaded inserts) | ||
| + | (use 1/8" end mill) | ||
| + | G0 G49 G40 G54 G90 X0 Y0 | ||
| + | G64 P0.001 | ||
| + | |||
| + | #1 = 25 (Y length) | ||
| + | #2 = 25 (X width) | ||
| + | #3 = 4 (increments) | ||
| + | #4 = 0.1 (z safe) | ||
| + | |||
| + | #11 = 0 (X) | ||
| + | #12 = 0 (Y) | ||
| + | |||
| + | o105 SUB | ||
| + | G91 X0.2275 | ||
| + | G90 G0 Z0 | ||
| + | G91 | ||
| + | G3 I-0.2275 Z-0.125 F80 | ||
| + | G3 I-0.2275 | ||
| + | G0 X-0.2275 | ||
| + | |||
| + | X0.1175 | ||
| + | G3 I-0.1175 Z-0.725 P6 F80 | ||
| + | G3 I-0.1175 | ||
| + | G0 X-0.1175 | ||
| + | |||
| + | G90 G0 Z#4 | ||
| + | o105 ENDSUB | ||
| + | |||
| + | o107 SUB | ||
| + | #11 = 0 | ||
| + | o106 while [#11 LT #2] | ||
| + | G90 G0 X[#11] | ||
| + | o105 CALL [#1] [#2] [#3] [#4] [#5] | ||
| + | G0 Z[#5] | ||
| + | #11 = [#11+#3] | ||
| + | o106 endwhile | ||
| + | #11 = 0 (reset) | ||
| + | o107 ENDSUB | ||
| + | |||
| + | |||
| + | M3 S1 M8 | ||
| + | /G4 P20 | ||
| + | |||
| + | |||
| + | o106 while [#12 LT #2] | ||
| + | o107 CALL [#1] [#2] [#3] [#4] [#5] | ||
| + | G91 G0 Y[#3] | ||
| + | #12 = [#12+#3] | ||
| + | o106 endwhile | ||
| + | |||
| + | |||
| + | |||
| + | M5 M9 | ||
| + | G90 | ||
| + | G28 | ||
M30 | M30 | ||
% | % | ||
</pre> | </pre> | ||
Latest revision as of 08:29, 9 March 2015
Square-Circle Test: Creates a 4in square folled by a 4in circle inside of the square. This is the code that we use to calibrate the machines.% G54 G90 G20 G0 G64 P0.01 M3 S1 G0 X0 Y2 G1 Z0 F150 Y0 X4 Y4 X0 Y2 G3 I2.0 G0 Z1 M5 X0 Y0 M30 %
Tool Sensor Test: This code will loop through tools 1-4 to prove that the tool sensor is working. This calls the tool, measures the length, drives it to zero, then pauses for 3 seconds before calling the next tool.
% G54 G20 G90 G0 X0 Y0 G64 P0.005 #1 = 1 o100 CALL [#1] G0 X0 Y0 G1 Z0 F50 G4 P3 #1 = 2 o100 CALL [#1] G0 X0 Y0 G1 Z0 F50 G4 P3 #1 = 3 o100 CALL [#1] G0 X0 Y0 G1 Z0 F50 G4 P3 #1 = 4 o100 CALL [#1] G0 X0 Y0 G1 Z0 F50 G4 P3 M30 %
Counter-bored Hole Pattern: This code will create a pattern of counterbored holes in your spoilboard using an 1/8" end mill. This program demonstrates nested loops.
%
(create counterbored holes for threaded inserts)
(use 1/8" end mill)
G0 G49 G40 G54 G90 X0 Y0
G64 P0.001
#1 = 25 (Y length)
#2 = 25 (X width)
#3 = 4 (increments)
#4 = 0.1 (z safe)
#11 = 0 (X)
#12 = 0 (Y)
o105 SUB
G91 X0.2275
G90 G0 Z0
G91
G3 I-0.2275 Z-0.125 F80
G3 I-0.2275
G0 X-0.2275
X0.1175
G3 I-0.1175 Z-0.725 P6 F80
G3 I-0.1175
G0 X-0.1175
G90 G0 Z#4
o105 ENDSUB
o107 SUB
#11 = 0
o106 while [#11 LT #2]
G90 G0 X[#11]
o105 CALL [#1] [#2] [#3] [#4] [#5]
G0 Z[#5]
#11 = [#11+#3]
o106 endwhile
#11 = 0 (reset)
o107 ENDSUB
M3 S1 M8
/G4 P20
o106 while [#12 LT #2]
o107 CALL [#1] [#2] [#3] [#4] [#5]
G91 G0 Y[#3]
#12 = [#12+#3]
o106 endwhile
M5 M9
G90
G28
M30
%