Difference between revisions of "PBX-BB rev4.1"

Revision as of 12:21, 17 February 2014

PBX-BB

Model: PBX-BB BeagleBone Breakout Board

Breakout Board Specs:

BeagleBone or BeagleBone Black Compatible
Screw Terminals or 5x PBX-Headers
RF Isolated Inouts and Outputs
15 Outputs and 5 Inputs
Integrated 5V/2A Logic Supply Regulator
USB Powered BeagleBone

Description:

The PBX-BB is the new CNC breakout board for the BeagleBone. It works perfectly with Charles Steinkuehler's Beaglebone port of LinuxCNC. It features 15 total outputs and 5 inputs, all software mappable to whichever signals you need. The PBX-BB features the same RF isolation circuitry found on the popular PBX-RF, protecting the Beaglebones' sensitive 1.8V and 3.3V circuitry from potentially damaging noise and spikes that can come from high voltage stepper motor drives.

The PBX-BB has 5x PBX-Headers (Figure 1) for easy connections to our stepper drivers and relay boards. Additional signals are present on the screw terminals for driving up to 5 motors and 4 relays.

New on the PBX-BB is a 5V/2A switching regulator that accepts voltages up to 76VDC. The efficiency of a switching regulator reduces heat. The 5V rail is bussed out to the PBX-Headers just like our other breakout boards, allowing you to drive the logic supply of the drivers from a single power source.

Figure 1: PBX Header

Getting Started

Burn our custom Machinekit Iso Image to an 8GB Sandisk MicroSD Card using Win32DiskImager
Install the MicroSD card, plug the BBB ethernet connector into your network, hold down the SD boot button, and apply power. The first time the image boots, it can take up to 5 minutes.
The Machinekit image uses DHCP. Run a port scanner such as Advanced IP Scanner to find the ip address of the BBB (or 'arp -a' from a command prompt). It should have only two ports open (80 and 22).
Install XMing and Putty.
Turn on X11 forwarding in Putty and connect to the BBB.
Username: linuxcnc

Password: linuxcnc
Launch LCNC by typing 'linuxcnc &' into the shell. The LCNC software, while running on the BBB, will forward its window onto your PC. Choose the PBX-BB configuration. On future sessions, simply launch LCNC with the PBX-BB config by using the 'last configuration' switch 'linuxcnc -l &'.
Use WinSCP and Notepad++ to edit the config files. When you choose 'edit' from WinSCP and allow WinSCP to open the file in Notepad++, whenever you make a change and save the file, WinSCP will automatically re-upload the changed file to the BBB.

Resources:

File:PBX-BB.configs.zip
Machinekit Iso Image
BeagleBone
http://bb-lcnc.blogspot.com/2013/07/adding-homelimit-switches.html

@@ Line 34: / Line 34: @@
 == Getting Started ==
 # Burn our custom [https://drive.google.com/file/d/0B5vTOfoZpyAXVWk0NWFPQ3E3R00/edit?usp=sharing Machinekit Iso Image] to an 8GB Sandisk MicroSD Card using [http://sourceforge.net/projects/win32diskimager/ Win32DiskImager]
-# Install the MicroSD card, plug the BBB ethernet connector into your network and apply power. The first time the image boots, it can take up to 5 minutes.
+# Install the MicroSD card, plug the BBB ethernet connector into your network, hold down the SD boot button, and apply power. The first time the image boots, it can take up to 5 minutes.
 # The Machinekit image uses DHCP. Run a port scanner such as [http://www.advanced-ip-scanner.com/ Advanced IP Scanner] to find the ip address of the BBB (or 'arp -a' from a command prompt). It should have only two ports open (80 and 22).
 # Install [http://sourceforge.net/projects/xming/ XMing] and [http://www.putty.org/ Putty].