Revision as of 07:22, 4 September 2015

http://www.craftycnc.com/touch-probes/

http://www.ebay.com/itm/171912530881

http://meshlab.sourceforge.net/

http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Touch_Probe

http://www.timeguy.com/cradek/01262579508

http://lab.whitequark.org/notes/2014-07-06/g38-probing-workpieces-in-linuxcnc/

http://www.scorchworks.com/Blog/auto-probing-with-g-code-ripper/

http://www.scorchworks.com/Gcoderipper/gcoderipper.html

LinuxCNC is distributed with gridprobe.ngc and smartprobe.ngc

( gridprobe.ngc                                                         )
( Rectangular Probing                                                   )
(                                                                       )
( This program repeatedly probes in a regular XY grid and writes the    )
( probed location to the file 'probe-results.txt' in the same directory )
( as the .ini file                                                      )

(Configuration section)
G20   (Inches)
F4    (probe speed)

#1=0  (X start)
#2=.25 (X increment)
#3=13 (X count)

#4=0
#5=.25
#6=5 (Y count)

#7=.1 (Z safety)
#8=-.5 (Z probe)
(End configuration section)

(PROBEOPEN probe-results.txt)
#9=0 #10=0
G0Z#7
O1 while [#9 lt #6]
    #10=0
    G0 Y[#4+#5*#9]
    O2 while [#10 lt #3]
        O3 if [[#9/2] - fix[#9/2] eq 0]
            G0X[#1+#2*#10]
        O3 else      
            G0X[#1+#2*[#3-#10-1]]
        O3 endif
        G38.2Z#8
        G0Z#7
        #10=[#10+1]
    O2 endwhile
    #9=[#9+1]
O1 endwhile

(PROBECLOSE)
G0Z#7
G0X#1Y#4
M2

(probe-hole.ngc)
O<probe-hole> sub
G20 F25

#1000=#1 ;max radius

G91 G38.3 Z.00001
#1001=#5061
#1002=#5062

G91 G38.2 X#1000
#1003=#5061
G90 G0 X#1001
G91 G38.2 X[0-#1000]
#1004=#5061
#1001=[[#1003+#1004]/2]
G90 G0 X#1001

G91 G38.2 Y#1000
#1005=#5062
G90 G0 Y#1002
G91 G38.2 Y[0-#1000]
#1006=#5062
#1002=[[#1005+#1006]/2]
G90 G0 Y#1002


G91 G38.2 X#1000
#1003=#5061
G90 G0 X#1001
G91 G38.2 X[0-#1000]
#1004=#5061
#1001=[[#1003+#1004]/2]
G90 G0 X#1001

G91 G38.2 Y#1000
#1005=#5062
G90 G0 Y#1002
G91 G38.2 Y[0-#1000]
#1006=#5062
#1002=[[#1005+#1006]/2]
G90 G0 Y#1002


F0.1

G90 G0 X[#1003-0.005]
G91 G38.2 X0.010
#1003=#5061
G90 G0 X[#1004+0.005]
G91 G38.2 X-0.010
#1004=#5061
#1001=[[#1003+#1004]/2]
G90 G0 X#1001

G90 G0 Y[#1005-0.005]
G91 G38.2 Y0.010
#1005=#5062
G90 G0 Y[#1006+0.005]
G91 G38.2 Y-0.010
#1006=#5062
#1002=[[#1005+#1006]/2]
G90 G0 Y#1002
G91 G1 F1 X[0-#5071] Y[0-#5072]
G90

#1007=[#1003-#1004+[6.0/25.4]]
#1008=[#1005-#1006+[6.0/25.4]]
#1009=[[#1007+#1008]/2]
#1010=[atan[#1002]/[#1001]]
#1011=[sqrt[[#1001*#1001]+[#1002*#1002]]]

(debug,Dia #1009 Ang #1010 Dist #1011)
O<probe-hole> endsub