Difference between revisions of "Unity-M"
From PROBOTIX :: wiki
m |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[Category:Controllers]] | + | [[Category:CNC Controllers]] |
| − | [[ | + | |
| + | [[File:Unity-M_rear.png|thumb|500px|Unity-M Controller]] | ||
| + | |||
[[Unity Controller]] customized for use with bench-top mill conversions using a higher amp Z driver with NEMA34 motor options. | [[Unity Controller]] customized for use with bench-top mill conversions using a higher amp Z driver with NEMA34 motor options. | ||
| + | * Expandable to your needs, versatile, and flexible. | ||
| + | * Can be used for 2, 3, or 4 axis systems. | ||
| + | * Get it with or without motors | ||
| + | * Motors (if purchased) are pre-wired with 6 Feet of 5-Conductor 22 Gauge Motor Wire and XLR connectors | ||
| + | |||
| + | == Have A Look Inside: == | ||
| + | * 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation | ||
| + | * Professionally wired, installed, mounted and tested electronics | ||
| + | * 4 Drivers, Breakout Board, IDC cables, and wired connector ports | ||
| + | * Full Enclosure with Power switch, fan, and fuses | ||
| + | * Modular and organized | ||
| + | |||
| + | == Driver System: == | ||
| + | * 3x 5.6Amp MondoStep Bipolar Drivers (X, Y, and A axis) | ||
| + | * 1x 7.8Amp MondoStep BiPolar Driver (Z axis) | ||
| + | |||
| + | == Breakout Board: == | ||
| + | The [[PBX-MX]] is an isolated parallel port breakout board for use with software such as LinuxCNC or Mach3. | ||
| − | + | == Integrated back panel includes: == | |
| + | * Connections for up to 4 motors | ||
| + | * Connector for limit switches | ||
| + | * Connector for E-Stop | ||
| + | * Earth ground connection for improved EMI protection | ||
| + | * Auxilary 5v logic output that can drive an accessory like the Powerswitch Tail | ||
| + | * IEC power connections for the primary power and the router control relay | ||
| + | * PBX-MX Isolated Parallel Port breakout board | ||
| + | * Two AC inputs | ||
| + | * Color coded | ||
== Pin-Out == | == Pin-Out == | ||
Latest revision as of 06:56, 23 August 2019
Unity Controller customized for use with bench-top mill conversions using a higher amp Z driver with NEMA34 motor options.
- Expandable to your needs, versatile, and flexible.
- Can be used for 2, 3, or 4 axis systems.
- Get it with or without motors
- Motors (if purchased) are pre-wired with 6 Feet of 5-Conductor 22 Gauge Motor Wire and XLR connectors
Contents
Have A Look Inside:
- 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation
- Professionally wired, installed, mounted and tested electronics
- 4 Drivers, Breakout Board, IDC cables, and wired connector ports
- Full Enclosure with Power switch, fan, and fuses
- Modular and organized
Driver System:
- 3x 5.6Amp MondoStep Bipolar Drivers (X, Y, and A axis)
- 1x 7.8Amp MondoStep BiPolar Driver (Z axis)
Breakout Board:
The PBX-MX is an isolated parallel port breakout board for use with software such as LinuxCNC or Mach3.
Integrated back panel includes:
- Connections for up to 4 motors
- Connector for limit switches
- Connector for E-Stop
- Earth ground connection for improved EMI protection
- Auxilary 5v logic output that can drive an accessory like the Powerswitch Tail
- IEC power connections for the primary power and the router control relay
- PBX-MX Isolated Parallel Port breakout board
- Two AC inputs
- Color coded
Pin-Out
|
1) A Dir | 10) X Limit |
| 2) X Step | 11) Y Limit | |
| 3) X Dir | 12) NC | |
| 4) Y Step | 13) Z Limit | |
| 5) Y Dir | 14) 120VAC Relay | |
| 6) Z Step | 15) E-stop | |
| 7) Z Dir | 16) 5VDC AUX | |
| 8) NC | 17) A Step | |
| 9) NC | 18-25) GND |
|
1) Pin 15 |
| 2) GND |
|
1) X Limit (Pin 10) |
| 2) GND | |
| 3) Y Limit (Pin 11) | |
| 4) GND | |
| 5) NC (Pin 12) | |
| 6) GND | |
| 7) Z Limit (Pin 13) | |
| 8) GND |
|
1) B- |
| 2) B+ | |
| 3) NC | |
| 4) A+ | |
| 5) A- |