Search results
Create the page "Power Supply" on this wiki! See also the search results found.
- *[[:Category:Power Supply|Power Supply]]3 KB (387 words) - 14:32, 8 November 2021
- :*Integrated 5V/2A Logic Supply Regulator ...oards, allowing you to drive the logic supply of the drivers from a single power source.4 KB (576 words) - 03:17, 18 November 2016
- === Are your power supplies compatible with my voltage? === ...The 24V switching power supplies has a switch on the side of them. The 40V power supplies need to be wired as described here: http://www.probotix.com/downlo15 KB (2,578 words) - 11:28, 23 October 2018
- * 10V - 44V Supply * Wide range of motor power (10-42V)6 KB (977 words) - 10:42, 29 September 2018
- which has the power to drive the opto-couplers. The relay side of the opto-couplers require a 5VDC power supply. A 1 amp or1 KB (244 words) - 18:01, 25 November 2013
- The PBX-2 has a built in LM317 based voltage regulator section that will supply 1.5AMPS @ +5V to the driver outputs of this interface. It also connects to The LM317 is rated for 40VDC, so you can wire it up to the same power supply as the motors. You may want to run it off of a WalWart to provide an additi3 KB (456 words) - 10:28, 29 September 2018
- * 8V - 32V Power Supply ...sults in reduced audible motor noise, increased step accuracy, and reduced power dissipation. The SideStep is one of the smallest stepper driver boards in i7 KB (1,125 words) - 10:42, 29 September 2018
- * Integrated 5V Logic Supply Regulator * USB Powered Logic Supply for PC Side5 KB (811 words) - 10:31, 9 March 2018
- ...tor driver kit comes with the motors, motor drivers, breakout board, power supply, DB25 cable, and IDC cable to connect the drivers to the breakout board. The basic motor driver kit comes with a basic 24V switching type power supply.6 KB (927 words) - 22:15, 22 July 2018
- ...and relay controlled 110V outlet (mounted to the back of the carriage) to power your spindle. All you need to provide is the router and tooling, CAM softwa ...switches, spindle control relay, cable chain, and carriage mounted spindle power jack, no other machine on the market comes close to being this complete, an7 KB (1,177 words) - 18:34, 20 January 2015
- *Standard with any 40V Linear Power supply or Large Machine997 B (148 words) - 10:44, 13 March 2019
- ...imit switches, spindle control relay, cable chain, carriage mounted router power jack, and complete LinuxCNC control PC with keyboard, mouse, monitor, & jog ...have to do is connect the motor and switch jacks, attach it to the PC, and power it on.5 KB (808 words) - 17:50, 27 May 2018
- ...and relay controlled 110V outlet (mounted to the back of the carriage) to power your spindle. All you need to provide is the router and tooling, CAM softwa ...switches, spindle control relay, cable chain, and carriage mounted spindle power jack, no other machine on the market comes close to being this complete, an7 KB (1,178 words) - 17:51, 27 May 2018
- * Integrated 5V/2A Logic Supply Regulator ...oards, allowing you to drive the logic supply of the drivers from a single power source.2 KB (317 words) - 09:21, 12 March 2020
- * 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation * Full Enclosure with Power switch, fan, and fuses.5 KB (813 words) - 12:51, 7 January 2022
- ...upply module that can accept up to 76VDC input and outputs a clean 2A@5VDC power rail.1 KB (246 words) - 12:26, 22 June 2018
- ...ered under warranty. Customer is responsible for rewiring the linear power supply if outside the USA - unless agreed upon in advance by PROBOTIX that we will10 KB (1,630 words) - 13:32, 27 December 2021
- [[Category:Power Supply]]138 B (20 words) - 10:40, 17 March 2018
- [[Category:Power Supply]]120 B (17 words) - 16:20, 22 July 2018
- * 40Volt (110VAC Input) Linear Power Supply for the fastest motor operation * Full Enclosure with Power switch, fan, and fuses2 KB (262 words) - 07:56, 23 August 2019